Quick answer
Why won't my washer drain or spin?
Most washers won't spin until they have drained, so the usual culprit is a clogged pump filter, a kinked drain hose or a failed drain pump. A faulty lid switch or door lock, or an unbalanced load, can also stop the spin.
A washer that ends a cycle with water still in the drum, or clothes that come out dripping, usually has one of two problems: the water can’t get out, or the washer won’t spin because something is stopping it. They’re closely linked. Most washers won’t spin until they’ve drained, so a drain problem often looks like a spin problem.
Safety First
Unplug the washer before working on it. Expect water when you open the pump filter or disconnect the hose. Have towels, a shallow pan and a bucket ready. If the cycle used hot water, wait for it to cool.
Step 1: Try a Drain and Spin Cycle
Select Drain & Spin (or Rinse & Spin) and run it on its own. If the washer drains and spins normally, the problem may be the load or the cycle you used. If it doesn’t drain, keep going.
Step 2: Check the Drain Hose
- Pull the washer out carefully and look for kinks or a crushed section behind it.
- Check that the hose isn’t pushed too far into the standpipe. If it goes in too deep, water can siphon back or the hose can block. Whirlpool, for example, recommends no more than 4.5 inches of hose in the standpipe, and Samsung suggests 6 to 8 inches with no extension.
- Check the hose height. It needs to rise above the water level in the tub, but not beyond the manufacturer’s maximum. Samsung calls for at least 18 inches high, and Maytag top-loaders specify the hose end at least 36 inches off the floor.
- If the standpipe or laundry sink backs up when the washer drains, the house drain is the problem.
Step 3: Clean the Drain Pump Filter (Front-Loaders)
Most front-load washers have a small access door at the bottom front. Behind it is a coin trap or pump filter that catches socks, coins, hair ties and lint before they reach the pump.
- Unplug the washer.
- Open the access panel.
- If there’s a small drain tube, pull it out, unplug it and let water drain into a pan. This can take several pans.
- Slowly unscrew the filter counter-clockwise. More water will come out.
- Remove debris from the filter and the opening. Shine a flashlight inside and check that the pump impeller turns.
- Screw the filter back in firmly so it doesn’t leak.
Many top-load washers don’t have a user-accessible filter, so a clog there may need a technician.
Step 4: Check the Lid or Door Lock
Washers won’t spin unless the lid or door is locked. If the lock doesn’t engage, the washer may fill and wash but never reach spin. Close the lid or door firmly, and look for broken latches. Codes such as LG dE (door not closed) and dE2 (closed but not locked), Samsung dC/dE, and Whirlpool F5 E2 point here.
Step 5: Rebalance the Load
If the washer drains but won’t spin or spins only slowly, the load may be unbalanced. A single heavy item (a bath mat, a pair of jeans, a duvet) can stop the drum from reaching high speed. Redistribute items or add a couple of towels. LG washers show UE for this.
Step 6: Suds
Too much detergent, or regular detergent in an HE washer, creates suds that slow draining and stop the spin. Some washers show Sud or Sd. Run a rinse cycle with no detergent and use the recommended amount of HE detergent next time.
Common Drain Codes by Brand
| Brand | Code | Meaning |
|---|---|---|
| LG | OE | Can’t drain |
| Samsung | 5C / 5E | Drain error |
| Whirlpool | F9 E1 | Long drain (over about 8 minutes) |
| Maytag | drn / F9 E1 | Long drain |
| Kenmore (some HE models) | F21 | Commonly indicates no drain within 8 minutes |
When It’s a Part Failure
If the hose is clear, the filter is clean and the lid locks, the cause is often a part:
- Drain pump: hums but doesn’t move water, or is silent.
- Lid lock or door lock assembly: won’t lock, so the washer won’t spin.
- Drive motor, belt or motor coupling: no spin despite draining.
- Control board or pressure sensor: washer doesn’t “know” it has drained.
When to Call a Pro
Call a technician if the washer still won’t drain after you’ve checked the hose and filter, the pump hums or is silent, the drum won’t spin with a balanced load, or codes return. Washers are heavy and full of water, and replacing a pump or lock is easier and safer with the right tools.
See our washer repair service. We fix LG, Samsung, Whirlpool, Maytag, Kenmore and more.
Book a repair: call 437-662-1414 or book a visit online. We’re open 7 AM to 11 PM every day, statutory holidays included, at the same price, and we serve Toronto, North York, Scarborough and Etobicoke. The $70 service call is waived when you go ahead with the repair, and our repairs carry a 3 to 6 month warranty depending on the job. We’ve been fixing appliances since 2004 with licensed, insured and certified technicians. Read our 350+ Google reviews.
Frequently Asked Questions
Why won’t my washer drain?
Common causes are a kinked drain hose, a clogged pump filter, a blocked standpipe, too many suds, or a failed drain pump. Start with the hose and filter.
Why does my washer drain but not spin?
Usually the load is unbalanced or the lid or door lock isn’t engaging. A worn belt, motor coupling or motor can also stop the spin.
How do I drain a washer full of water?
Unplug it. On a front-loader, use the small drain tube behind the bottom access panel, then remove the pump filter. On a top-loader, you may need to lower the drain hose into a bucket or bail the water out.
Where is the drain filter on my washing machine?
On most front-load washers, it’s behind a small door at the bottom front of the machine. Many top-load washers don’t have a user-serviceable filter.