Dishwasher Not Draining: Brand-by-Brand Codes and Fixes

Dishwasher Not Draining: Brand-by-Brand Codes and Fixes

Quick answer

How do I reset a dishwasher drain error?

Clear the cause first: clean the filter, check the drain hose and the sink or disposer connection. Then turn off the breaker for a few minutes, restore power and run a short rinse or drain cycle to clear the code.

Every dishwasher drains the same basic way: water passes through a filter, a pump pushes it out through a hose, and it leaves through the sink drain, air gap or garbage disposer. But each brand reports problems differently, and some have specific quirks. This guide goes brand by brand. For the general causes, start with our guide to a dishwasher not draining.

Safety First

Switch off the dishwasher’s breaker (or unplug it) before you reach into the filter or pump area. Put towels down and check for broken glass.

Drain Codes at a Glance

BrandCodeMeaning
BoschE24Drain hose or outlet blocked or kinked
BoschE25Drain pump blocked or pump cover loose
BoschE22Commonly indicates dirty filters
Whirlpool / Maytag / KitchenAidF9 E1Long drain
Frigidaire / Electroluxi20Dishwasher didn’t drain
Frigidaire / Electroluxi40Clogged filter
GEC1Pump-out took longer than 2 minutes
GEC3Won’t drain
Samsung5C / 5EDrain error
LGOEDrain error

Codes vary between models and generations, so always confirm with your owner’s manual.

Bosch

Bosch splits drain problems into two codes. E24 points outside the machine: a kinked hose, a clogged sink connection, or the knockout plug left in a new garbage disposer. E25 points inside: something stuck in the drain pump or a pump cover that isn’t seated. Under the filter you’ll find a small cover you can lift with a spoon handle to clear the pump. Our Bosch E24 and E25 guide has the full steps.

Whirlpool, Maytag and KitchenAid

These brands share a lot of engineering. F9 E1 means a long drain: the dishwasher took too long to empty.

  1. Clean the filter assembly at the bottom of the tub. Many models have an upper and lower filter that twist out.
  2. Check the drain hose under the sink for kinks.
  3. Run the disposer, and check for a knockout plug if it’s new.
  4. Clear the air gap if there is one.

If the code returns, the drain pump or a blockage in the sump may need professional attention.

Frigidaire and Electrolux

i20 means the dishwasher didn’t drain. i40 means the filter is clogged. These brands specify that the drain hose should reach at least 32 inches high. A low hose can let water siphon back.

  1. Clean the filter (especially if you see i40).
  2. Check the hose height and loop.
  3. Check the sink drain and disposer.
  4. Reset by pressing Cancel or unplugging the dishwasher (or switching off the breaker) for 3 minutes.

GE

GE uses C1 when the pump-out takes longer than 2 minutes and C3 when it won’t drain.

  • Clean the air gap on the counter, if present.
  • Check the drain hose and run the disposer.
  • Clean the filter.
  • For C3, switch off the breaker for 30 seconds, restore power and try again.

Samsung

Samsung dishwashers show 5C or 5E for drain problems, depending on the model. Clean the filter at the bottom of the tub, check the hose for kinks and the sink drain for blockages, then run a cycle. If you see OC or oE, that commonly indicates an over-level condition, meaning too much water, which can also be related to drain problems. If you see LC or LE, that’s a leak sensor detecting moisture, not a drain code.

LG

LG dishwashers show OE for a drain error. Clean the filter, check for kinks in the hose, and make sure the sink drain and disposer are clear. An AE or E1 code points to a leak instead.

Miele

Miele dishwashers usually display drain problems as a plain-language “drain fault” or a fault code depending on the model. Start with the filter combination at the base of the tub, then check the hose. Miele manuals describe how to reach the drain pump on many models.

Universal Checks for Every Brand

  • Filter clean and properly locked in.
  • Drain hose not kinked, with a high loop or air gap.
  • Garbage disposer empty and knockout plug removed.
  • Sink drain flowing freely.
  • Only dishwasher detergent used. Dish soap makes suds that can cause drain and overflow errors.

When to Call a Pro

Call a technician if a drain code keeps coming back after you’ve cleaned the filter and checked the hose, disposer and air gap, or if the pump hums without draining. A failed drain pump, check valve or control board needs proper diagnosis, and the dishwasher often has to come out from under the counter.

Our dishwasher repair team works on all of these brands, including Whirlpool and Frigidaire.

Book a repair: call 437-662-1414 or book a visit online. We’re open 7 AM to 11 PM every day, statutory holidays included, at the same price, and we serve Toronto, North York, Scarborough and Etobicoke. The $70 service call is waived when you go ahead with the repair, and our repairs carry a 3 to 6 month warranty depending on the job. We’ve been fixing appliances since 2004 with licensed, insured and certified technicians. Read our 350+ Google reviews.

Frequently Asked Questions

What does F9 E1 mean on a Whirlpool dishwasher?

F9 E1 means a long drain. The dishwasher took too long to empty. Clean the filter, check the drain hose and disposer, and clear the air gap.

What is the i20 code on a Frigidaire dishwasher?

i20 means the dishwasher didn’t drain. Clean the filter, check that the drain hose loops up to at least 32 inches, clear the sink drain, then reset with Cancel or by cutting power for 3 minutes.

What does C1 mean on a GE dishwasher?

C1 means the pump-out took longer than 2 minutes. Clean the air gap, check the drain hose, and run the garbage disposer.

How do I reset a dishwasher drain error?

Clear the cause first. Then, depending on the brand, press Cancel, hold Start/Reset, or switch off power for a few minutes. If the code returns, book a repair.