Samsung Washer 4C Error Code – Causes and How to Fix It

Samsung Washer 4C Error Code – Causes and How to Fix It

Quick answer

How do I fix a 4C error on my Samsung washer?

Open both water taps fully, straighten the inlet hoses, and clean the small filter screens where the hoses connect to the washer. Then unplug the washer for 5 minutes and run Rinse+Spin. If it still won’t fill, the water inlet valve likely needs replacing.

A 4C code on a Samsung washer means the machine isn’t getting enough water. It tried to fill, waited, and the water level didn’t rise the way it expected, so it stopped the cycle. Older Samsung models show the same fault as 4E. Most of the time the cause is outside the washer: a closed tap, a kinked hose or a clogged inlet screen. Here’s how to work through it.

One thing first: Samsung dishwashers also use a 4C code, and there it means something different. This guide is for Samsung washers.

Safety First

Unplug the washer before you pull it out or remove any hoses. Turn off both water taps before you disconnect the inlet hoses, and keep a towel and a small bucket handy, because the hoses will hold some water.

Step 1: Check the Water Taps

  1. Find the hot and cold taps behind the washer or above the laundry sink.
  2. Turn both fully on (counter-clockwise). A tap that’s only half open can trigger 4C on a cold fill.
  3. If the washer is new or someone recently worked on the plumbing, make sure the taps weren’t left off.
  4. Run the laundry sink tap if you have one. If the water pressure is weak there too, the problem is the house supply, not the washer.

Step 2: Straighten the Inlet Hoses

  1. Pull the washer forward gently, enough to see behind it.
  2. Look for kinks, sharp bends or a hose crushed against the wall. Condo laundry closets are tight, and this is very common after a washer has been pushed back.
  3. Make sure the hot hose goes to the hot inlet and the cold hose to the cold inlet.
  4. Replace any hose that is bulging, cracked or very old. Braided stainless hoses are a good upgrade.

Step 3: Clean the Inlet Filter Screens

Each water inlet on the back of the washer has a small mesh screen. Sediment, rust flakes and debris from plumbing work collect there and slowly choke the flow.

  1. Unplug the washer and turn off both taps.
  2. Unscrew the inlet hoses from the back of the washer and let them drain into the bucket.
  3. Look into each inlet. If the screen is covered with grit, pull it out carefully with needle-nose pliers.
  4. Rinse the screens under the tap with an old toothbrush, then push them back in.
  5. Reconnect the hoses hand-tight plus a quarter turn, turn the taps on, and check for drips.

Step 4: Check the Drain Hose Height

If the drain hose sits too low or is pushed too far down the standpipe, water can siphon out while the washer is filling. The washer never reaches its level and shows 4C. The end of the drain hose should be hooked into the standpipe, not sealed into it, and the hose should loop up above the water level in the drum.

Step 5: Reset and Test

  1. Unplug the washer (or switch off its breaker) for 5 minutes.
  2. Plug it back in and run Rinse+Spin.
  3. Watch the first minute. You should hear the water valve open and see water entering through the detergent drawer.

If it fills normally and the code doesn’t return, you’re done.

What If the 4C Code Keeps Coming Back?

  • Failed water inlet valve. If you hear a click or hum but no water flows with the taps fully open and clean screens, the valve coil or valve body has likely failed.
  • Water level (pressure) sensor. The washer may be filling fine but not “seeing” the water. A blocked sensor hose or a faulty sensor gives a false 4C.
  • Frozen supply line. In a garage or an unheated space in winter, the hose or pipe can freeze. Let it thaw before running the washer.
  • Control board. Less common, but possible if the valve and sensor test fine.

Other Samsung Washer Codes You Might See

CodeMeaningFirst step
5C / 5E / SCDrain problemClean the debris filter and check the drain hose
UE / UBUnbalanced loadRedistribute the load and level the washer
dC / dE / dSDoor not closed or not lockingClose the door firmly and clear the gasket
3C / 3EMotor problemLighten the load and reset

For the drain codes, see our guide to Samsung washer SC, 4C and 5C codes. Samsung’s own washer error code guide lists the codes by model type.

When to Call a Pro

Call a technician if the taps are fully open, the hoses are straight, the screens are clean and the washer still won’t fill, or if you hear the valve click with no water. Testing the inlet valve and the water level sensor needs a multimeter and access inside the cabinet.

See our Samsung appliance repair page and our washer repair service.

Book a repair: call 437-662-1414 or book a visit online. We’re open 7 AM to 11 PM every day, statutory holidays included, at the same price, and we serve Toronto, North York, Scarborough and Etobicoke. The $70 service call (plus HST) is waived when you go ahead with the repair, and if a part has to be ordered, the return visit is free. Warranty depends on the part and the manufacturer. We’ve been fixing appliances since 2004 with licensed, insured and certified technicians. Read our Google reviews.

Frequently Asked Questions

How do I fix a 4C error on my Samsung washer?

Open both water taps fully, straighten the inlet hoses, and clean the small filter screens where the hoses connect to the washer. Then unplug the washer for 5 minutes and run Rinse+Spin. If it still won’t fill, the water inlet valve likely needs replacing.

Is 4C the same as 4E on a Samsung washer?

Yes. Both mean the washer isn’t getting enough water. Newer models show 4C and older models show 4E.

Can low water pressure cause a 4C code?

Yes. If the house pressure is low or a tap is only partly open, the washer may not fill in time. Check the pressure at the laundry sink or another tap nearby.

Can I still use my Samsung washer with a 4C error?

Not until it can fill. The washer stops the cycle to avoid washing with too little water. Fix the supply problem first, then reset it.