Whirlpool Washer Error Codes: F9 E1, F8 E1, F5 E2, F7 E1 and More

Whirlpool Washer Error Codes: F9 E1, F8 E1, F5 E2, F7 E1 and More

Quick answer

What do Whirlpool washer error codes mean?

Whirlpool codes have two parts: the F number is the system and the E number is the fault. F9 E1 is a slow drain, F8 E1 means not enough water is coming in, and F5 E2 is a door lock problem. Unplug the washer for a minute to reset after fixing the cause.

Whirlpool washers use a code system in two parts: an F number for the system involved and an E number for the specific fault. Many Maytag washers share the same codes, since the brands share engineering. Here’s what the most common ones mean and what you can safely do about them.

Safety First

Unplug the washer before checking hoses, filters or the inside of the cabinet. Turn off the water taps before disconnecting inlet hoses. Have towels ready.

Whirlpool Washer Codes at a Glance

CodeMeaningDIY first step
F9 E1Long drain (more than about 8 minutes)Check drain hose and pump filter
F8 E1 / LO FLLow fill / water not filling fast enoughOpen taps, check inlet hoses and screens
F5 E2Door lock problemClose door firmly, check for obstructions
F7 E1Motor speed problemCheck for shipping bolts on a new washer, rebalance load
Sd / SudExcess suds detectedUse less HE detergent, run a rinse

Codes can differ between models. Your manual or the tech sheet inside the washer’s cabinet will confirm.

F9 E1: Long Drain

The washer took more than about 8 minutes to drain.

  1. Check the drain hose for kinks behind the machine.
  2. Check how far the hose goes into the standpipe. Whirlpool recommends no more than 4.5 inches inside it. Too deep can cause siphoning or a poor seal, which leads to drain problems.
  3. Clean the pump filter if your model has one (on many front-loaders, behind a small panel at the bottom front).
  4. Check the standpipe and household drain. If water backs up out of the standpipe, the house drain is clogged.
  5. Too many suds can also slow draining.

Maytag washers show the same issue as drn or F9 E1, and specify that the hose end should be at least 36 inches off the floor.

F8 E1 or LO FL: Low Fill

The washer isn’t getting water fast enough.

  1. Make sure both hot and cold taps are fully open.
  2. Check the inlet hoses for kinks.
  3. Turn off the taps, disconnect the hoses at the washer, and check the small screens in the inlet valve. Clean them gently if they’re clogged with sediment.
  4. Check your home’s water pressure. If other taps are weak, the issue is the supply.
  5. In winter, make sure hoses in a cold space haven’t frozen.

Maytag shows this as LF or F8 E1.

F5 E2: Door Lock

The washer couldn’t lock the door (front-loaders) or lid (top-loaders).

  • Close the door or lid firmly.
  • Check that nothing is caught in the door, such as a sleeve or the edge of a towel.
  • Unplug for a minute and restart.
  • If the code returns, the lock assembly or its wiring may need replacement.

F7 E1: Motor Speed

The control detected a problem with how fast the motor is turning.

  • New washer? Check that the shipping bolts were removed from the back. Running with them installed can cause errors and damage.
  • Redistribute the load. One heavy item can overload the motor.
  • Check that the drum turns freely by hand (power off).
  • If the code persists, it may be the motor, drive system or control, which needs a technician.

Sd or Sud: Too Many Suds

The washer sensed excess suds and paused to clear them.

  • Use only HE detergent and follow the dosing line. Concentrated detergents need less.
  • Don’t add extra detergent for heavily soiled loads; use a stronger cycle instead.
  • Run a rinse cycle with no detergent to clear suds.

Kenmore Washers

Some Kenmore washers built by Whirlpool use similar codes. Certain Kenmore HE2 models commonly show F20 (no fill), F21 (no drain within 8 minutes) and F22 (door lock). Check your manual to confirm for your model.

How to Reset a Whirlpool Washer

  1. Press Pause/Cancel twice to cancel the cycle.
  2. Unplug the washer for about a minute (or switch off the breaker).
  3. Plug it back in and run a short cycle, such as Rinse & Spin.

Resetting clears the display, but if you haven’t fixed the cause, the code will return. For general drain or spin problems, see our guide to a washer not draining or spinning.

When to Call a Pro

Call a technician if a code returns after you’ve checked hoses, filters and the load, especially F7 E1 (motor) or F5 E2 (door lock) that won’t clear. These usually involve a part replacement and testing inside the washer.

See our Whirlpool appliance repair, Maytag repair and washer repair pages.

Book a repair: call 437-662-1414 or book a visit online. We’re open 7 AM to 11 PM every day, statutory holidays included, at the same price, and we serve Toronto, North York, Scarborough and Etobicoke. The $70 service call is waived when you go ahead with the repair, and our repairs carry a 3 to 6 month warranty depending on the job. We’ve been fixing appliances since 2004 with licensed, insured and certified technicians. Read our 350+ Google reviews.

Frequently Asked Questions

What does F9 E1 mean on a Whirlpool washer?

F9 E1 means a long drain. The washer took more than about 8 minutes to drain. Check the drain hose, how deep it sits in the standpipe, and the pump filter.

How do I fix F8 E1 on a Whirlpool washer?

F8 E1 means low fill. Open the hot and cold taps fully, straighten the inlet hoses, and clean the inlet valve screens. Low household water pressure can also cause it.

What does F5 E2 mean on a Whirlpool washer?

F5 E2 means the washer couldn’t lock the door or lid. Close it firmly and check for clothing caught in it. If it keeps happening, the lock may need replacing.

How do I reset my Whirlpool washer?

Cancel the cycle, unplug the washer for about a minute, then plug it back in and run Rinse & Spin. The code will return if the cause hasn’t been fixed.