Bosch Dishwasher E09 Error Code – Heating Problems and Solutions

Bosch Dishwasher E09 Error Code – Heating Problems and Solutions

Quick answer

What does E09 mean on a Bosch dishwasher?

E09 means the dishwasher has a problem in its heating circuit, so the water isn’t heating properly. Reset the dishwasher at the breaker for 10 minutes and clean the filter. If E09 returns, the heater pump, its wiring or the control board needs testing.

An E09 code on a Bosch dishwasher means there’s a fault in the heating circuit. Most Bosch dishwashers don’t have an exposed heating element. They use a heat pump: a circulation pump with a heater built in. When the control board can’t get the water up to temperature, it shows E09. The usual signs are dishes that come out cool, greasy or still wet. Some E09 codes are a one-off glitch, but if the code keeps coming back, the heater pump or its wiring usually needs replacing.

Safety First

Turn off the dishwasher at the breaker before you remove the filter or any panel. The heater runs on 120 V and is under the tub, so all testing should be done with the power off.

Step 1: Run Hot Water at the Sink First

A dishwasher connected to a long run of pipe may take in cold water at the start. Run the kitchen tap on hot until it’s hot, then start the dishwasher. This shortens the time the heater needs and can stop E09 on a weak but still working heater.

Step 2: Reset the Dishwasher

  1. Switch off the breaker for 10 minutes.
  2. Switch it back on, wait a minute, then choose a normal cycle.
  3. If E09 doesn’t come back on the next two or three cycles, it was likely a power glitch.

Step 3: Clean the Filter and Check Circulation

The heat pump needs a steady flow of water. A clogged filter starves it, and some models will flag a heating error.

  1. Remove the bottom rack.
  2. Twist out the cylindrical filter and lift out the flat mesh filter.
  3. Rinse both under the tap with a soft brush.
  4. Wipe out the sump underneath, then refit both filters until they lock.
  5. Spin the spray arms by hand to make sure they turn freely.

If the filter was badly clogged, our guide to a dishwasher not cleaning properly has more cleaning steps.

What If the E09 Code Keeps Coming Back?

  • Heater pump (heat pump). The heating element inside the circulation pump can fail open. This is the most common cause of a repeat E09.
  • Wiring or connector at the heat pump, often corroded from a small leak.
  • Control board relay that switches the heater.
  • Temperature sensor (NTC) giving the board a false reading.

A technician measures the heater’s resistance and checks voltage at the connector to find out which part is at fault, so you don’t pay for parts you don’t need.

Other Bosch Dishwasher Codes You Might See

CodeMeaningFirst step
E15Water in the base pan (leak protection)Power off, dry the base for 24 hours
E24Drain hose or drain blockedCheck the drain hose and sink connection
E25Drain pump blockedClean the filter and the pump cover
E22Filter blockedClean the filter and the sump

See our Bosch dishwasher E15 guide and our Bosch E24 and E25 guide. Bosch keeps a full dishwasher error code list.

When to Call a Pro

Call a technician if E09 comes back after a reset and a clean filter, if dishes come out cold every time, or if you see water or burn marks around the bottom of the dishwasher. Replacing the heater pump means removing the dishwasher from under the counter.

See our Bosch appliance repair page and our dishwasher repair service.

Book a repair: call 437-662-1414 or book a visit online. We’re open 7 AM to 11 PM every day, statutory holidays included, at the same price, and we serve Toronto, North York, Scarborough and Etobicoke. The $70 service call (plus HST) is waived when you go ahead with the repair, and if a part has to be ordered, the return visit is free. Warranty depends on the part and the manufacturer. We’ve been fixing appliances since 2004 with licensed, insured and certified technicians. Read our Google reviews.

Frequently Asked Questions

What does E09 mean on a Bosch dishwasher?

E09 means the dishwasher has a problem in its heating circuit, so the water isn’t heating properly. Reset the dishwasher at the breaker for 10 minutes and clean the filter. If E09 returns, the heater pump, its wiring or the control board needs testing.

Why are my Bosch dishes not drying and the dishwasher shows E09?

Bosch dishwashers rely on hot final rinse water to dry dishes. If the heater isn’t working, dishes stay wet and the board shows E09.

Is it worth repairing a Bosch dishwasher with E09?

Usually, yes. Bosch dishwashers are well built, and a heater pump replacement often costs much less than a new dishwasher, especially on newer models.

Can I still use my Bosch dishwasher with E09?

It may run, but dishes will come out poorly cleaned and wet. It’s best to get it checked before the problem gets worse.