Quick answer
How do I clean a front-load washer?
Wipe out the door gasket, clean the detergent drawer and the pump filter, then run the hot cleaning cycle with the drum empty. Do it about once a month and leave the door ajar between washes to stop smells and mould.
Front-load washers are efficient and gentle on clothes, but their sealed design traps moisture. Combine that with detergent and softener residue, and you get musty smells, black spots on the door seal, and sometimes grey streaks on laundry. A thorough clean takes under an hour. Here’s the full routine.
What You’ll Need
- Microfibre cloths and an old toothbrush
- Warm water and mild dish soap (for wiping, not for the wash cycle)
- A washer cleaner product, or bleach if your manual allows it
- A shallow pan and towels (for the pump filter)
- Rubber gloves
Safety First
Unplug the washer before cleaning the gasket, removing the detergent drawer, or opening the pump filter. Never mix bleach with vinegar, ammonia or other cleaners.
Step 1: Clean the Door Gasket
The rubber boot around the door opening is the most common source of odour.
- Pull back the folds of the gasket gently, all the way around.
- Remove hair, lint, coins, and any small items.
- Wipe the folds with warm, soapy water. Use a toothbrush in the crevices.
- For dark spots, use a diluted cleaner your manual approves. Rinse with a damp cloth.
- Dry the gasket thoroughly with a clean cloth.
Check the drain holes at the bottom of the gasket and clear any blockages. Look for tears too; a damaged gasket can leak.
Step 2: Clean the Detergent Drawer
- Pull the drawer out until it stops, then press the release tab (usually marked) and remove it.
- Separate any inserts, such as the softener cap.
- Soak them in warm water, then scrub off residue with a toothbrush.
- Clean the drawer cavity inside the washer. Mould often grows on its ceiling. Use a toothbrush and a damp cloth.
- Dry everything and reinstall.
Step 3: Clean the Drain Pump Filter
The pump filter catches small items and lint. If it’s clogged, water doesn’t drain well and odours build up.
- Lay towels and a shallow pan in front of the bottom access panel.
- Open the panel. If there’s a small drain tube, lower it into the pan and remove the cap to drain water. Repeat as needed.
- Unscrew the filter counter-clockwise, slowly.
- Remove debris and rinse the filter.
- Reinstall firmly, replace the drain tube cap, and close the panel.
Our guides to the LG OE code and Samsung 5C code walk through this for those brands.
Step 4: Run a Cleaning Cycle
Run your washer’s built-in cleaning cycle (Samsung Self Clean, LG Tub Clean, or similar) with an empty drum. Add a washer cleaner, or bleach if your manual permits, in the compartment the manual specifies. If your washer has no cleaning cycle, use the hottest, longest cycle with an empty drum. See our guide to Samsung Self Clean and LG Tub Clean for details.
Step 5: Wipe the Drum and Door Glass
After the cycle, wipe the inside of the drum and the door glass with a damp cloth. Dry the gasket again.
Step 6: Leave It Open
Leave the door and detergent drawer slightly open until everything is dry. Make this a habit after every wash.
Cleaning Schedule
| Task | How often |
|---|---|
| Leave door and drawer open | After every wash |
| Wipe the gasket | Weekly, or after heavy loads |
| Cleaning cycle | About monthly |
| Clean the detergent drawer | Monthly |
| Clean the pump filter | Every few months |
Habits That Prevent Odour
- Use HE detergent, and less of it. Excess detergent leaves residue that feeds odours.
- Go easy on fabric softener. It’s a major source of build-up.
- Move wet laundry to the dryer promptly.
- Wash on a hot cycle sometimes, if your fabrics allow it.
- Check pockets before every load.
Still Smells? Look Deeper
If the smell persists after a full clean, the cause may be a partial drain blockage, water sitting in the drain hose, or residue in hidden parts of the outer tub. If the washer also drains slowly or shows drain codes, see our guide to a washer not draining or spinning.
When to Call a Pro
Call a technician if the washer still smells after a full cleaning routine, the gasket is torn or leaking, the pump filter won’t come out, or drain codes keep returning. We can replace door gaskets and drain pumps, and check the drain system.
See our washer repair service and our LG repair page.
Book a repair: call 437-662-1414 or book a visit online. We’re open 7 AM to 11 PM every day, statutory holidays included, at the same price, and we serve Toronto, North York, Scarborough and Etobicoke. The $70 service call is waived when you go ahead with the repair, and our repairs carry a 3 to 6 month warranty depending on the job. We’ve been fixing appliances since 2004 with licensed, insured and certified technicians. Read our 350+ Google reviews.
Frequently Asked Questions
How often should I clean my front-load washer?
Run a cleaning cycle about once a month, wipe the gasket weekly, and clean the pump filter every few months. Leave the door open after every wash.
How do I get rid of black mould on my washer gasket?
Pull back the gasket folds, clean with warm soapy water and a toothbrush, and use a diluted cleaner your manual approves on stubborn spots. Dry it fully, and keep the door open between washes.
Can I use vinegar and bleach to clean my washer?
Never mix them; combining bleach with vinegar releases harmful fumes. Use one product at a time, only as your washer’s manual allows.
Why does my front-load washer smell even after cleaning?
Persistent odour may come from a partial drain blockage, a clogged pump filter, or residue in the outer tub. If it keeps happening, have a technician check the drain system.