LG Dryer nP Error Code – Dryer Not Heating

LG Dryer nP Error Code – Dryer Not Heating

Quick answer

What does nP mean on an LG dryer?

nP means the dryer isn’t getting full 240 V power to the heater, so it runs but doesn’t heat. Switch the dryer’s double breaker fully off, wait a minute and switch it back on, then make sure the plug is firmly in the outlet. If nP comes back, the cord, terminal block or heater needs checking.

An nP code on an LG electric dryer means the dryer isn’t getting the right power to the heater. It’s often called a “no power” or “no heat” code. The drum turns and the display works, but the clothes stay cold. That’s because an electric dryer needs 240 V for the heater and only 120 V for the motor and controls. If half of the power supply is missing, the dryer still runs but can’t heat, and LG flags nP. Most of the time the fix is at the breaker, not inside the dryer.

Safety First

Only reset the dryer’s breaker. Don’t open the electrical panel cover, test wiring in the panel or take the dryer’s terminal block cover off with the power on. If anything looks burnt or smells hot, stop and call an electrician or a technician.

Step 1: Reset the Double Breaker

  1. Find the dryer’s breaker in your panel. It’s a double breaker: two switches joined by a handle tie, usually 30 amps.
  2. Switch it fully off. Half of a double breaker can trip on its own and still look on, so don’t skip this.
  3. Wait 1 minute, then switch it firmly back on.

In many Toronto condos and apartments, the breaker is in a small panel inside the unit, often near the entrance or in the laundry closet.

Step 2: Check the Power Cord and Outlet

  1. Unplug the dryer.
  2. Check that the plug pushes fully and firmly into the outlet. A loose plug can lose one side of the power.
  3. Look at the plug and outlet for scorch marks or melted plastic. If you see any, don’t plug it back in. Call for service.
  4. Plug it back in fully.

Step 3: Reset and Test the Dryer

  1. Leave the dryer unplugged, or the breaker off, for 5 minutes.
  2. Restore power and run Normal on High for 10 minutes.
  3. Open the door and feel the air. If it’s warm and nP is gone, you’re done.

What If the nP Code Keeps Coming Back?

If the breaker and cord are fine and nP returns, the problem is inside the dryer or the supply circuit:

  • Terminal block where the cord connects to the dryer. Loose or burnt connections here are common.
  • Power cord that’s damaged inside.
  • Heater element that has burnt open.
  • Weak breaker or outlet. These are part of your home’s wiring and may need an electrician.
  • Control board that isn’t reading the voltage correctly.

Other LG Dryer Codes You Might See

CodeMeaningFirst step
d80 / d90 / d95Vent restricted (80%, 90%, 95%)Clean the lint filter and the vent
tE1 / tE2 / tE3Temperature sensor faultClean the vent and reset; call if it returns
PSPower supply problemCheck the cord and outlet; call
dE / d1Door openClose the door firmly

See our LG dryer tE1 guide, our LG d80, d90 and d95 guide and our post on a dryer not heating. LG has its own nP troubleshooting page and a full dryer error code list.

When to Call a Pro

Call a technician if nP comes back after a full breaker reset, if the dryer tumbles but stays cold, or if you see scorch marks at the plug. We check the cord, terminal block and heater. If the problem is in your home’s wiring, we’ll tell you so you can call an electrician.

See our LG appliance repair page and our dryer repair service.

Book a repair: call 437-662-1414 or book a visit online. We’re open 7 AM to 11 PM every day, statutory holidays included, at the same price, and we serve Toronto, North York, Scarborough and Etobicoke. The $70 service call (plus HST) is waived when you go ahead with the repair, and if a part has to be ordered, the return visit is free. Warranty depends on the part and the manufacturer. We’ve been fixing appliances since 2004 with licensed, insured and certified technicians. Read our Google reviews.

Frequently Asked Questions

What does nP mean on an LG dryer?

nP means the dryer isn’t getting full 240 V power to the heater, so it runs but doesn’t heat. Switch the dryer’s double breaker fully off, wait a minute and switch it back on, then make sure the plug is firmly in the outlet. If nP comes back, the cord, terminal block or heater needs checking.

Why does my LG dryer run but not heat with nP?

The motor and controls only need 120 V, but the heater needs the full 240 V. If one side of the power is missing, the drum turns but the dryer stays cold.

Does nP show on LG gas dryers?

The nP code is mainly an electric dryer code, because it checks the 240 V supply to the heater. We only repair electric dryers.

Can a tripped breaker cause nP even if it looks on?

Yes. Half of a double breaker can trip and stay in a middle position. Switch it fully off, then back on.