Samsung Washer UE Error Code – Washer Not Spinning

Samsung Washer UE Error Code – Washer Not Spinning

Quick answer

What does UE mean on a Samsung washer?

UE means the load is unbalanced, so the washer won’t spin at full speed. Spread the clothes evenly, check that the washer is level, then run Rinse+Spin. Some models show UB or Ub for the same problem.

If your Samsung washer stops before the spin and shows UE, it isn’t broken in the way it looks. UE means unbalanced load: the washer sensed the drum wobbling too much, tried to rebalance a few times, and then gave up rather than spin at high speed. Some models show UB or Ub instead. The symptom you notice is a washer that won’t spin and clothes that come out soaked, but the cause is almost always the load or the way the washer is sitting.

Safety First

Pause or cancel the cycle and wait for the door to unlock before reaching in. Unplug the washer before you tilt it, adjust its feet or look underneath. Front-loaders are heavy; get help before moving one.

Step 1: Redistribute the Load

  1. Open the door and untangle the load. Sheets wrapped around other items are the most common cause.
  2. Spread the items evenly around the drum.
  3. Wash a single heavy item (a bath mat, a duvet, a pair of jeans) with a couple of towels so the weight balances.
  4. Don’t overload. The drum should not be packed tight; you should be able to put your hand in above the clothes.
  5. Run Rinse+Spin.

Tip: Bulky items like comforters, pillows and waterproof mattress covers trap water in one spot. Use the Bedding or Bulky cycle if your washer has one.

Step 2: Check That the Washer Is Level

  1. Put a level on top of the washer, side to side and front to back.
  2. Rock the washer by pushing on opposite top corners. It should not move.
  3. Turn the feet to raise or lower each corner, then tighten the lock nuts up against the cabinet so the feet can’t drift.
  4. On a pedestal, check that the washer is secured to it and the pedestal feet are level too.

Old wooden floors in Toronto semis and houses often slope. A washer that was level when installed can creep out of level over time.

Step 3: Check the Shipping Bolts (New Washers)

If the washer is new or was just moved, look at the back. Front-load washers ship with three or four long bolts that lock the drum for transport. If they’re still in, the washer will shake violently and show UE. Remove them with a wrench and put the plastic caps from the accessory bag into the holes. Keep the bolts in case you move again.

Step 4: Reset and Test

  1. Unplug the washer for 5 minutes.
  2. Plug it back in and run Rinse+Spin with a small, mixed load.
  3. Watch the spin. A short wobble at the start is normal while the washer balances the load.

What If the UE Code Keeps Coming Back?

If the washer shows UE with a small, balanced load, or worse, with an empty drum, something mechanical is worn:

  • Shock absorbers or suspension springs (front-load) or suspension rods (top-load). When they wear out, the drum moves too much and the washer can’t balance.
  • Drum bearings. A roaring or grinding noise on spin, plus UE, usually means the bearings are going.
  • Motor or hall sensor. The washer uses the motor to measure balance. A faulty sensor can cause false UE codes.
  • Drain problem. A washer that can’t drain fully is heavy with water and may refuse to spin. If you also see standing water, read our guide to a washer not draining or spinning.

Other Samsung Washer Codes You Might See

CodeMeaningFirst step
4C / 4ENot enough water coming inOpen the taps fully and clean the inlet screens
5C / 5E / SCDrain problemClean the debris filter and check the drain hose
dC / dE / dSDoor not closed or not lockingClose the door firmly and clear the gasket
3C / 3EMotor problemLighten the load and reset

For water supply errors, see our Samsung washer 4C error code guide, and for drain errors our post on Samsung washer SC, 4C and 5C codes. Samsung also has an error code guide by washer type.

When to Call a Pro

Call a technician if UE shows up with small loads or an empty drum, if the washer bangs or walks across the floor on spin, or if you hear grinding from the drum. Replacing shocks, springs or bearings means taking the washer apart, and worn suspension parts get worse quickly.

See our Samsung appliance repair page and our washer repair service.

Book a repair: call 437-662-1414 or book a visit online. We’re open 7 AM to 11 PM every day, statutory holidays included, at the same price, and we serve Toronto, North York, Scarborough and Etobicoke. The $70 service call (plus HST) is waived when you go ahead with the repair, and if a part has to be ordered, the return visit is free. Warranty depends on the part and the manufacturer. We’ve been fixing appliances since 2004 with licensed, insured and certified technicians. Read our Google reviews.

Frequently Asked Questions

What does UE mean on a Samsung washer?

UE means the load is unbalanced, so the washer won’t spin at full speed. Spread the clothes evenly, check that the washer is level, then run Rinse+Spin. Some models show UB or Ub for the same problem.

Why does my Samsung washer say UE with a small load?

Very small loads, or a single heavy item, are hard to balance. Add a couple of towels. If it happens even with an empty drum, the shocks, springs or a sensor likely need service.

How do I reset the UE code on my Samsung washer?

Fix the load first, then unplug the washer for 5 minutes and run Rinse+Spin. The code clears once the washer can spin normally.

Can an unlevel floor cause a UE error?

Yes. If the washer rocks or sits on a sloped floor, it can’t balance the drum. Level it and lock the feet in place.