Quick answer
What are the most common LG dryer error codes?
The most common are d80, d90 and d95 (vent getting blocked), nP (not enough power to heat) and tE1 (temperature sensor fault). Clean the lint filter and vent for the d codes, reset the double breaker for nP, and call a technician if tE1 keeps coming back.
LG dryers show a short code on the display when something needs attention. Most LG dryer codes come down to four things: airflow, power, temperature sensors and the door. Some codes are reminders rather than faults: the d80, d90 and d95 “Flow Sense” codes tell you the vent is getting blocked while the dryer still works. This guide lists the common LG dryer error codes, what each one means and what you can safely check yourself. It covers electric LG dryers, which are the ones we repair.
Safety First
Unplug the dryer before you pull it out, touch the vent or remove any panel. LG electric dryers run on 240 V. Only reset a breaker; never open the electrical panel or the dryer’s terminal block with power on.
LG Dryer Error Codes Chart
| Code | Meaning | First step |
|---|---|---|
| d80 | Vent about 80% restricted | Clean the lint filter, check the vent |
| d90 | Vent about 90% restricted | Clean the vent duct and outside hood |
| d95 | Vent about 95% restricted | Stop using the dryer until the vent is cleaned |
| nP | No full 240 V power to the heater | Reset the double breaker fully off and on |
| tE1 / tE2 / tE3 | Temperature sensor (thermistor) fault | Clean the vent, reset; call if it returns |
| PS | Power supply wiring problem | Check the cord and outlet; call |
| dE / d1 | Door open or door switch problem | Close the door firmly; check the latch |
| AE | Water leak (steam models) | Check the steam water supply and hose |
| F1 | Control or sensor fault (varies by model) | Reset; call if it returns |
Codes can vary by model and year. LG’s dryer error code list lets you check yours.
Airflow Codes: d80, d90 and d95
LG’s Flow Sense measures how restricted your vent is. The higher the number, the worse the blockage. Clean the lint filter, check the duct behind the dryer for kinks and clean the vent to the outside. Full steps in our LG dryer d80, d90 and d95 guide and our post on how to clean a dryer vent.
Power Code: nP
The dryer runs but won’t heat because it isn’t getting full 240 V power. Switch the double breaker fully off and back on, and make sure the plug is pushed all the way in. See our LG dryer nP guide.
Temperature Codes: tE1, tE2 and tE3
The thermistor that measures air temperature is reading open or shorted. Clean the lint path and reset. If the code returns, the sensor or its wiring needs replacing. Read our LG dryer tE1 guide.
How to Reset an LG Dryer
- Press Power to turn the dryer off.
- Unplug it, or switch off the double breaker, for 5 minutes.
- Restore power and run a Timed Dry on High for 10 minutes.
A reset clears the display, but if the cause is still there, the code comes back.
Keep Codes Away
- Clean the lint filter before every load, and wash it every few months.
- Clean the vent duct at least once a year, more often with a long duct run.
- Use a rigid or semi-rigid metal duct, not foil or plastic.
- Don’t overload the drum.
- Keep the outside vent hood clear of snow and leaves in winter and fall.
When to Call a Pro
Call a technician if a code comes back after cleaning and a reset, if the dryer runs but stays cold, if it smells burnt or if the drum won’t turn. Heaters, thermistors, thermal fuses, terminal blocks and boards all need testing with the dryer opened up. If your dryer isn’t heating and there’s no code, see our guide to a dryer not heating.
See our LG appliance repair page and our dryer repair service, or book a visit.
Book a repair: call 437-662-1414 or book a visit online. We’re open 7 AM to 11 PM every day, statutory holidays included, at the same price, and we serve Toronto, North York, Scarborough and Etobicoke. The $70 service call (plus HST) is waived when you go ahead with the repair, and if a part has to be ordered, the return visit is free. Warranty depends on the part and the manufacturer. We’ve been fixing appliances since 2004 with licensed, insured and certified technicians. Read our Google reviews.
Frequently Asked Questions
What are the most common LG dryer error codes?
The most common are d80, d90 and d95 (vent getting blocked), nP (not enough power to heat) and tE1 (temperature sensor fault). Clean the lint filter and vent for the d codes, reset the double breaker for nP, and call a technician if tE1 keeps coming back.
How do I reset my LG dryer?
Unplug the dryer, or switch off its double breaker, for 5 minutes. Then restore power and run Timed Dry on High.
Can I keep using my LG dryer with a d80 code?
Yes, d80 is an early warning, but clean the vent soon. At d95, stop using the dryer until the vent is cleaned, because a blocked vent is a fire risk.
Why is my LG dryer not heating with no error code?
Common causes are a blown thermal fuse, a burnt-out heater element or a blocked vent. See our dryer not heating guide or call for a diagnosis.